OXVA VPrime 2 Dual Mesh Replacement Pods XL

OXVA VPrime 2 Dual Mesh Replacement Pods XL 6ml

Keep your VPrime performing at its best with the new-generation OXVA VPrime 2 Dual Mesh Replacement Pods. Officially named the OXVA VPRIME Dual Mesh Cartridge, each refillable pod combines a built-in dual-mesh coil, a generous 6ml XL capacity and OXVA's upgraded UNITECH 3.0 airflow platform.

These pods are designed for the OXVA VPrime 2 Pod Vape Kit, where they unlock selectable Boost and Eco operation. They are also physically compatible with the original OXVA VPrime device, although mode control depends on the device being used.

Key Features

• New-generation OXVA VPrime Dual Mesh cartridge
• UNITECH 3.0 dual-mesh coil technology
• 6ml XL refillable e-liquid capacity per pod
• Choose 0.4 Ohm or 0.6 Ohm resistance
• Side-fill port with a secure silicone seal
• Built-in coil - replace the complete pod when the coil reaches the end of its life
• Compatible with OXVA VPrime 2 and original OXVA VPrime devices
• Boost and Eco modes available when used with VPrime 2
• Enhanced airflow and leak-resistant internal design
• Two pods of the selected resistance in each pack

0.4 Ohm vs 0.6 Ohm - Which VPrime 2 Pod Should You Choose?

*Use these figures as a starting guide only. Follow the wattage marked on the pod or packaging, begin at the lower end and increase gradually. Boost mode produces a stronger output than Eco mode, so choose an e-liquid strength appropriate for the vapour produced.

For suitable liquids, browse our 50/50 vape e-liquid and 70/30 high-VG e-liquid collections. Unsure about inhale styles? Read our MTL vs DTL guide.

Dual Mesh, Boost Mode and Eco Mode Explained

Each cartridge contains two mesh heating elements. When the pod is paired with the VPrime 2, Boost Mode activates the dual-mesh system for a stronger, denser output, while Eco Mode uses a more efficient single-mesh operating pattern for a smoother vape and reduced power demand.

OXVA describes the 0.4 Ohm pod in Boost mode as delivering performance comparable with approximately 0.2 Ohm output, while the 0.6 Ohm version is compared with approximately 0.3 Ohm output. These are performance comparisons in Boost mode - the actual pod variants sold in this listing remain 0.4 Ohm and 0.6 Ohm.

Device Compatibility

Need a tighter MTL draw, a 0.8 Ohm option or the earlier single-mesh cartridge? View the separate original OXVA VPrime replacement pods. You can also explore the complete OXVA vape range or browse all replacement vape pods.

How to Fill and Prime the OXVA VPrime Dual Mesh Pod

1. Remove the pod from the device.
2. Lift the silicone seal covering the side-fill port.
3. Insert the e-liquid bottle nozzle into the fill opening, avoiding the central airflow channel.
4. Fill slowly, leave a small air gap and close the silicone seal firmly.
5. When using a fresh pod, allow the cotton to saturate fully before vaping.
6. Begin at the lower end of the recommended power range and adjust gradually to taste.

Care Tips for Better Pod Performance

• Do not overfill the cartridge or leave the fill seal partly open.
• Wipe condensation from the pod base and device contacts regularly.
• Keep the pod upright where practical, especially after filling.
• Avoid repeated draws without a pause, as the wick needs time to resaturate.
• Replace the complete pod if flavour becomes muted, vapour falls noticeably, a burnt taste develops or the cartridge is damaged.

Product Specifications

What's in the Box?

• 2 x OXVA VPrime Dual Mesh 6ml XL replacement pods in your selected resistance

Device and e-liquid are sold separately.

For adults aged 18 and over. This listing is specifically for the XL 6ml version. Check any destination or local restrictions that apply before ordering.